http://www.toyotanation.com/forum/showthread.php?t=302817&highlight=starter+solenoid+fry+burn
My '93 Camry is having a problem somewhere between the ignition and the starter. When I turn the key, it turns, the electrical comes on, but the engine does not turn at all, no clicking, nothing.A gentleman showed me how to essentially hotwire it by disconnecting the ignition switch and using a wire directly from the battery to the starter, and it turns fine and starts. So the starter is not getting a charge to start.The next day, reconnected the ignition switch to try it, and it worked just like normal all day. I thought it was fixed. However, on day three, it stopped again, and I returned to the hotwire situation.
Things I've Tried:-Charge directly to starter, works fine, no problem with starter.-Cleaned battery, it has a good connection.-Tried turning key in park and neutral, will not start in either, no turnover or engine or clicking.-The fact that the engine started normally on day two implies that there is not problem with the ignition switch.Any ideas? Is there anything else in the relay that could be bad? I'd really like to save some money and try fixing this at home before I give up and take it to a garage.
Listen very carefully when it doesn't start and see if you hear 1 click. If so, you could have the common worn starter solenoid contacts problem. If this is the case, do a search on this forum for "starter contacts" and read up on the problem and it's cures. You can also test for this problem when it doesn't start by taking a hammer or a wrench and tapping on the starter's solenoid and then try to start the car. If the car now starts you have identified this problem.
This is what a starter relay looks like:http://www.rockauto.com/catalog/moreinfo.php?pk=939378
$11.30+shipping
Relay, starter solenoid, or wiring. DO not exchange your starter out to any repair place, they built these starters to last forever. Just have the solenoid rebuilt if they advise it and it is normal for it to wear out eventually, if you use the starter allot, basically the solenoid pushes live electrical copper contact points that are connected directly to your battery to get to a larger motor can run and turn the motor over. The above poster pointed out to the rebuild for the contacts if need be, it very simple, as is taking the starter off the car. Then go to the starter repair shop and ask for the contacts, but read the writeup on it first as it tells you everything. Also, check your wiring, could be loose, weak or old battery itself, or bad battery connection can fool the troubleshooting procedure. Volt meter will check your relay. Usually, a simple and cheap repair, the contacts themselves should be only a few dollars. Happy trails.
startercontacts.com Don't replace that DENSO starter.
If your starter is clicking a few times but then turns over normally it most likely just has bad contacts. Occasionally the problem can be the wiring or the ignition switch. If so you may need to install a relay.
Friday, January 29, 2010
Sunday, January 24, 2010
Camry Starter Solenoid Contact problem
http://www.toyotanation.com/forum/showthread.php?threadid=27312&forumid=10


If you are hearing 1 click, you have the very common "starter solenoid contact problem". The contacts inside the starter's solenoid wear and no longer allow current to pass throught them to the starter. This results in a no crank situation. Do a search on this forum for "starter contacts". It has been covered numerous times.
You can verify this the next time it happens.Have someone hold the key in the start position while you get out and give the starter a tap with a hammer or good size wrench. If the starter now cranks the engine, you have verified the starter solenoid contact problem. You will need to replace the starter's solenoid contacts or replace the entire starter with a new or rebuilt unit.
One other option is to remove your starter from the vehicle and take it in to an auto electrical rebuilder in your area to have your original starter rebuilt. This is an option I prefer if you have the original OEM Toyota starter. However, these rebuilders are becoming harder to find all the time.
If you are hearing multiple rapid clicks then you have a battery problem, an alternator problem where the alternator is not charging the battery, a loose alternator belt again resulting in the alternator not charging the battery, or a problem with poor/corroded connections at the battery posts/terminals or at the starter itself.
Testing Camry ignition Switch
http://www.justanswer.com/questions/2j349-i-have-a-1993-toyota-camry-4-door-2-2-4cyl-problems-are-no


The connector of the ignition switch looks like the second diragram.
1 . To gain acccess, remove upper and lower steering column covers (it may be necessary to first remove lower instrument panel trim panel). Remove outer plastic trim cover from lock cylinder assembly (if equipped).
2 . Disconnect ignition switch electrical connector(s). Remove screw(s) retaining ignition switch to lock cylinder. Remove ignition switch from lock cylinder. To install, reverse removal procedure.
Above are removal pocedures for the ignition switch. After removing the steering covers you would be able to notice the ignition switch , at opposite end of where the ignition key is inseterd.
You would need a DVOM for continuity tests. If you have a test light, backprobing the terminals Read more: http://www.justanswer.com/questions/2j349-i-have-a-1993-toyota-camry-4-door-2-2-4cyl-problems-are-no#ixzz0dZsouJfy


The symptoms described indicates a fault with the ignition switch. Here are procedures for testing the ignition switch.
IGNITION SWITCH Disconnect ignition switch connector. With ignition switch in specified position, check continuity between specified terminals of ignition switch connector. If continuity is not as specified, replace ignition switchRead more: http://www.justanswer.com/questions/2j349-i-have-a-1993-toyota-camry-4-door-2-2-4cyl-problems-are-no#ixzz0dZrxv2RT
IGNITION SWITCH Disconnect ignition switch connector. With ignition switch in specified position, check continuity between specified terminals of ignition switch connector. If continuity is not as specified, replace ignition switchRead more: http://www.justanswer.com/questions/2j349-i-have-a-1993-toyota-camry-4-door-2-2-4cyl-problems-are-no#ixzz0dZrxv2RT
Terminal 4 and 10 should be hot at all times.Read more: http://www.justanswer.com/questions/2j349-i-have-a-1993-toyota-camry-4-door-2-2-4cyl-problems-are-no#ixzz0dZsITjfh
The connector of the ignition switch looks like the second diragram.
1 . To gain acccess, remove upper and lower steering column covers (it may be necessary to first remove lower instrument panel trim panel). Remove outer plastic trim cover from lock cylinder assembly (if equipped).
2 . Disconnect ignition switch electrical connector(s). Remove screw(s) retaining ignition switch to lock cylinder. Remove ignition switch from lock cylinder. To install, reverse removal procedure.
Above are removal pocedures for the ignition switch. After removing the steering covers you would be able to notice the ignition switch , at opposite end of where the ignition key is inseterd.
You would need a DVOM for continuity tests. If you have a test light, backprobing the terminals Read more: http://www.justanswer.com/questions/2j349-i-have-a-1993-toyota-camry-4-door-2-2-4cyl-problems-are-no#ixzz0dZsouJfy
Toyota Camry Problems
http://repairpal.com/cars/toyota/camry
Brakes
The front brake rotors can wear causing a pulsation felt in the brake pedal when it is applied.
Our technicians recommend flushing the brake fluid every 60,000 miles because the fluid can become dirty and may cause problems in the brake system such as early failure of the master cylinder or wheel cylinders.
Engine
The motor mount on the passenger side of the car can wear out on cars with high mileage. This will put extra stress on the other mounts, and the faulty mount will need to be replaced.
It is important to regularly check the valve clearance as the exhaust valves may become too tight. This will lead to valve failures, which are expensive to repair. 2.0L 4 cylinder
The ignition coil inside the distributor may fail. Our technicians tell us this may result in a hesitation on acceleration, especially when the vehicle is warming up on cold, rainy days.
Exhaust & Emissions
The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and to clean off the EGR Temperature sensor. Our technicians tell this repair is all pretty straight forward and takes about 1-1.5 hours.
By the time the EGR system is plugged, the Oxygen Sensor is getting slow or 'lazy'. When servicing or cleaning the EGR system, it is a good idea to replace the Oxygen sensor because it works in tandem with the EGR system.
Suspension & Steering
The power steering pump and power steering hoses tend to develop leaks, particularly in the V6 models.
Driving over bumps causes loud, annoying noises in the body of the car. If the noise is a groaning or creaking, it can be improved by lubricating the rubber joints in the suspension system. If the noise is a rattling sound, the problem is likely wear and tear on the upper mounting plate for the strut suspension.
Drive Train
At higher mileages, (125,000-150,000) the automatic transmissions may not shift correctly. This can be caused by the Throttle Position Sensor being out of adjustment or a shift solenoid needing to be replaced. Typically the transmission does not need to be completely overhauled.
Electrical & Lights
If the vehicle will not crank over, the most common problem is the starter, which tend to fail at about 100,00-125,000 miles. Sometimes it is only the starter solenoid contacts, but often the complete starter (including solenoid) needs to be replaced.
Heating & Air Conditioning
Usually by 150,000 miles the A/C system will need some attention, especially in climates where it is used often. Our technicians tell us that it is best to service the A/C system every 2-3 years. This keeps the moisture in the system at a minimum which extends the life of the components.
Brakes
The front brake rotors can wear causing a pulsation felt in the brake pedal when it is applied.
Our technicians recommend flushing the brake fluid every 60,000 miles because the fluid can become dirty and may cause problems in the brake system such as early failure of the master cylinder or wheel cylinders.
Engine
The motor mount on the passenger side of the car can wear out on cars with high mileage. This will put extra stress on the other mounts, and the faulty mount will need to be replaced.
It is important to regularly check the valve clearance as the exhaust valves may become too tight. This will lead to valve failures, which are expensive to repair. 2.0L 4 cylinder
The ignition coil inside the distributor may fail. Our technicians tell us this may result in a hesitation on acceleration, especially when the vehicle is warming up on cold, rainy days.
Exhaust & Emissions
The EGR System tends to get restricted or blocked with carbon after 100,000- 125,000 miles which will cause an emissions test failure for NOX. If the EGR system is equipped with an EGR temperature sensor it will trigger a Check Engine Light for improper EGR flow. The repair is to clean out the EGR passages and to clean off the EGR Temperature sensor. Our technicians tell this repair is all pretty straight forward and takes about 1-1.5 hours.
By the time the EGR system is plugged, the Oxygen Sensor is getting slow or 'lazy'. When servicing or cleaning the EGR system, it is a good idea to replace the Oxygen sensor because it works in tandem with the EGR system.
Suspension & Steering
The power steering pump and power steering hoses tend to develop leaks, particularly in the V6 models.
Driving over bumps causes loud, annoying noises in the body of the car. If the noise is a groaning or creaking, it can be improved by lubricating the rubber joints in the suspension system. If the noise is a rattling sound, the problem is likely wear and tear on the upper mounting plate for the strut suspension.
Drive Train
At higher mileages, (125,000-150,000) the automatic transmissions may not shift correctly. This can be caused by the Throttle Position Sensor being out of adjustment or a shift solenoid needing to be replaced. Typically the transmission does not need to be completely overhauled.
Electrical & Lights
If the vehicle will not crank over, the most common problem is the starter, which tend to fail at about 100,00-125,000 miles. Sometimes it is only the starter solenoid contacts, but often the complete starter (including solenoid) needs to be replaced.
Heating & Air Conditioning
Usually by 150,000 miles the A/C system will need some attention, especially in climates where it is used often. Our technicians tell us that it is best to service the A/C system every 2-3 years. This keeps the moisture in the system at a minimum which extends the life of the components.
Saturday, January 23, 2010
Tuesday, January 19, 2010
1996 Camry oil pressure switch location
1998 Toyota Camry 4 cyl Two Wheel Drive Automatic 185000 miles
----------------------------------------------------------------
We have an oil leak at a "fitting" on the front of the engine, passenger side just below the head gasket. The oil just squirts out at the seal of the "fitting". Can you help me identify what component would be located in this area and is it easily replaceable? Thanks.
Re: where is the camry oil pressure switch location?
07/26/2007, 1:36PM
Re: where is the camry oil pressure switch location?
07/26/2007, 1:36PM
The oil pressure sender is located on the engine block near where the oil filter screws on. It should have one wire coming out of it and be a roughly hex-shaped metal unit threaded into the block.
On your 1996 TOYOTA CAMRY, the OIL PRESSURE SWITCH is: UNDER HOOD, CENTER, LOWER ENGINE AREA, MOUNTED ON FRONT DRIVER SIDE OF ENGINE
I have to be completely honest with you here that oil pumps do not fail on these cars, the only problem we ever see is some issues with dry seals at the pump that can cause some oil leaks.
Thursday, January 14, 2010
Resetting Camry maint interval light
Okay here is the biggest mistake: Ignore what the manual says about how to reset the MAINT REQD light. Its completely wrong. In fact, the first hint should have been when it said there was a MAINT REQD SOON light. I shined a flashlight at the dash to see what all the possible indicators are, and there is no MAINT REQD SOON light... anyway, I have an LE model with a I4. If someone else has a different trim level or v6, and I'm wrong correct me.
anyway, here is what you do to reset the MAINT REQD light so it will quit blinking:
a) With the Engine ON click your Odometer/TripA/TripB selector knob so the display shows TRIP A
b) Turn the car off
c) Turn the key 1 click to ACC (accessory mode)
d) While in ACC, press and hold the selector knob in (don't worry that can't see anything on the dashboard.)
e) While you are still holding the selector knob, click the key 1 more position to the ON position.
f) If you do it correctly, you will see the TripA display change to somenumbers and then start blinking quickly.
you will also see the MAINTREQD blinking quickly.
After about 5 seconds of holding the knob inthe display should show 0000000000000 then go away.
Start the car up, and no more MAINT REQD light until you put another 4500miles on the car!
anyway, here is what you do to reset the MAINT REQD light so it will quit blinking:
a) With the Engine ON click your Odometer/TripA/TripB selector knob so the display shows TRIP A
b) Turn the car off
c) Turn the key 1 click to ACC (accessory mode)
d) While in ACC, press and hold the selector knob in (don't worry that can't see anything on the dashboard.)
e) While you are still holding the selector knob, click the key 1 more position to the ON position.
f) If you do it correctly, you will see the TripA display change to somenumbers and then start blinking quickly.
you will also see the MAINTREQD blinking quickly.
After about 5 seconds of holding the knob inthe display should show 0000000000000 then go away.
Start the car up, and no more MAINT REQD light until you put another 4500miles on the car!
Subscribe to:
Posts (Atom)

